Two weeks ago we discussed the concept of periodisation, and compared the traditional and block periodisation models. If you missed that article, please click here. Block periodisation recommends the inclusion of short specialised mesocycles (blocks), repeated continually throughout a training year. We recommend that athletes begin a 16 week macrocycle with the ‘General Preparation’ block or phase. The main objective of this mesocycle is to prepare the musculoskeletal system for the subsequent phases where volume and intensity are increased. The main goals of this training phase are increases in functional strength and muscular endurance.
As previously discussed, each block should consist of key training sessions which target similar adaptations. During the ‘General Preparation’ phase, the key training sessions should consist of strength or torque intervals. Torque is the rotational force applied to the pedals during each pedal stroke. It is calculated by multiplying the force applied to the pedals, by the crank length (lever arm). Crank length will be constant, so torque is really an indicator of the force applied to the pedal. Torque is an important variable for cyclists to consider, because power is the product of torque and angular velocity (cadence). Should a cyclist improve the amount of torque they are able to produce at the same cadence, they should by definition, improve the power they are able to produce.
Strength or Torque intervals, also often referred to as over- or big-gear intervals, are simply performed through sustaining a high power output at a low cadence. We will now show explain how to perform a set of torque intervals, and demonstrate how to analyse one of these workouts.
6 x 4 minutes of torque work
A key session to perform during the ‘General Preparation’ block is 6 x 4 minute torque or strength intervals. We will now break down how to perform this session.
If you are using a power meter, we would strongly recommend that you perform a manual calibration before the start of your warm up, and possibly before the start of your first interval. The calibrations will increase the reliability of your measurements.
Each training session should begin with a good warm up, and 30 minutes should be sufficient. If you are performing the session outdoors and it is particularly cold, you may want to increase the length of the warm up. Conversely, if you are performing the session indoors, a shorter warm up may be sufficient.
These intervals are best performed on a steady, steep gradient (8-12%) where you can use a gear you are just able to turn over at a cadence of between 40 - 50 rpm. Focus should be on the complete pedal stroke, keeping your shoulders and hands relaxed during climbs while focusing on a stable pelvis.
Push the lap button at the start and end of each interval in order to mark the intervals. This will help you analyse your session once it is completed.
Once you have completed the final interval, cool down in order to improve your recovery for subsequent sessions that may follow later in the week. Once again, a 30 minute cool down should be sufficient.
We recommend that you try and use the same hill/gradient for each interval, because this will provide you with consistent data to analyse. Figure 2 is an example of a torque session performed by one of our athletes. Each interval of the session was performed on the same climb which made the intervals a lot more consistent and analysing the session a lot easier.
The outcome of this workout should be the amount of torque (Nm) produced in each interval, and not power output (W). Lowering the cadence (selecting a harder gear), increases the force that is applied to the pedals which will increase the torque (Nm) produced (Figure 3). The relationship between torque and power output will be different during these intervals compared to your usual high-cadence efforts. This is also illustrated in the warm up and cool down periods in Figure 3.
Figure 3: The relationship between torque and power output. During periods of high cadence (warm up and cool down), where easier gears are used, torque is low compared to the low cadence (hard gear) intervals.
A great way to track your progression during the ‘General Preparation’ block is to analyse these sessions, and plot the torque values for each of the 4 minute intervals, add them all together and divide by the total number of intervals (6 or 8 depending on the session). This will provide you with the average for the set of intervals. The graph below shows how we plot an athlete’s progression during their block. The first two sessions went well, but the third session shows a decrease in the amount of torque produced. The drop in torque was most likely due to some acute fatigue, so we allowed for a slightly longer rest before the next session and they were able to produce their best numbers in the two subsequent sessions.
If you do not have the software to be able to calculate Torque, you may calculate crank torque by using the following equation:
If you do not have a power meter, focus on the cadence and gear selection. You will be able to track your improvements by being able to push a bigger gear at the same cadence for the same session.
As a reference, elite male cyclists are producing around 1.5 Nm/kg of body mass during a 4 minute torque interval session.